Advanced search
1 file | 4.10 MB Add to list

Severe plastically deformed commercially pure aluminum : substructure, micro-texture and associated mechanical response during uniaxial tension

Harishchandra Lanjewar (UGent) , Soroosh Naghdy (UGent) , Florian Vercruysse (UGent) , Leo Kestens (UGent) and Patricia Verleysen (UGent)
Author
Organization
Abstract
Severe plastic deformation (SPD) of metals to obtain ultra-fine or even nano-sized grains has proven to be an interesting concept explored over the last few decades. However, the mechanical behavior of SPD metals and the underlying microstructural phenomena are not fully understood yet. In present work, commercially pure aluminum was subjected to high pressure torsion (HPT) deformation with strains ranging from very low levels to values well in the steady-state microstructure regime. The mechanical properties of the HPT processed samples were determined using tensile tests on miniature samples using full-field strain mapping. Orientation imaging microscopy (OIM) was utilized to follow the progression of grain refinement and texture as a function of imposed SPD. Local orientation based misorientation gradients helped to perform statistical boundary analysis and determine the fractions of incidental and geometrically necessary dislocation (GND) boundaries and local GND densities. From probability density distributions of the misorientation gradients two different stages of microstructural evolution, namely, fragmentation and saturation, could be discerned. The strength increased monotonously and the uniform elongation, though lower than the value of the annealed material, enhanced with the imposed strain in HPT. The post-necking response was observed to be highly microstructure dependent, where a lower grain size augmented the resistance for micro-crack propagation and enhanced the elongation-to-failure. In addition, the work hardening response corresponding to the yield point displayed maxima coinciding with the onset of the saturation stage. Anisotropy in fracture strain, observed between the axial and radial directions in a disk-like HPT sample, reduced with the randomization of shear texture, while higher intensities of the C {100}<110> orientation was considered responsible for the lower elongation-to-failure along the radial direction.
Keywords
High pressure torsion, Commercial purity aluminum, Statistical boundary analysis, Tensile properties, Micro-texture, Work hardening, CHANNEL ANGULAR EXTRUSION, STRAIN-HARDENING BEHAVIOR, HALL-PETCH RELATION, RATE SENSITIVITY, STORED ENERGY, DISLOCATION BOUNDARIES, DEFORMATION STRUCTURES, NEUTRON-DIFFRACTION, NANOCRYSTALLINE, DUCTILITY

Downloads

  • (...).pdf
    • full text (Published version)
    • |
    • UGent only
    • |
    • PDF
    • |
    • 4.10 MB

Citation

Please use this url to cite or link to this publication:

MLA
Lanjewar, Harishchandra, et al. “Severe Plastically Deformed Commercially Pure Aluminum : Substructure, Micro-Texture and Associated Mechanical Response during Uniaxial Tension.” MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, vol. 764, 2019.
APA
Lanjewar, H., Naghdy, S., Vercruysse, F., Kestens, L., & Verleysen, P. (2019). Severe plastically deformed commercially pure aluminum : substructure, micro-texture and associated mechanical response during uniaxial tension. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 764.
Chicago author-date
Lanjewar, Harishchandra, Soroosh Naghdy, Florian Vercruysse, Leo Kestens, and Patricia Verleysen. 2019. “Severe Plastically Deformed Commercially Pure Aluminum : Substructure, Micro-Texture and Associated Mechanical Response during Uniaxial Tension.” MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 764.
Chicago author-date (all authors)
Lanjewar, Harishchandra, Soroosh Naghdy, Florian Vercruysse, Leo Kestens, and Patricia Verleysen. 2019. “Severe Plastically Deformed Commercially Pure Aluminum : Substructure, Micro-Texture and Associated Mechanical Response during Uniaxial Tension.” MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 764.
Vancouver
1.
Lanjewar H, Naghdy S, Vercruysse F, Kestens L, Verleysen P. Severe plastically deformed commercially pure aluminum : substructure, micro-texture and associated mechanical response during uniaxial tension. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING. 2019;764.
IEEE
[1]
H. Lanjewar, S. Naghdy, F. Vercruysse, L. Kestens, and P. Verleysen, “Severe plastically deformed commercially pure aluminum : substructure, micro-texture and associated mechanical response during uniaxial tension,” MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, vol. 764, 2019.
@article{8635156,
  abstract     = {Severe plastic deformation (SPD) of metals to obtain ultra-fine or even nano-sized grains has proven to be an interesting concept explored over the last few decades. However, the mechanical behavior of SPD metals and the underlying microstructural phenomena are not fully understood yet. In present work, commercially pure aluminum was subjected to high pressure torsion (HPT) deformation with strains ranging from very low levels to values well in the steady-state microstructure regime. The mechanical properties of the HPT processed samples were determined using tensile tests on miniature samples using full-field strain mapping. Orientation imaging microscopy (OIM) was utilized to follow the progression of grain refinement and texture as a function of imposed SPD. Local orientation based misorientation gradients helped to perform statistical boundary analysis and determine the fractions of incidental and geometrically necessary dislocation (GND) boundaries and local GND densities.

From probability density distributions of the misorientation gradients two different stages of microstructural evolution, namely, fragmentation and saturation, could be discerned. The strength increased monotonously and the uniform elongation, though lower than the value of the annealed material, enhanced with the imposed strain in HPT. The post-necking response was observed to be highly microstructure dependent, where a lower grain size augmented the resistance for micro-crack propagation and enhanced the elongation-to-failure. In addition, the work hardening response corresponding to the yield point displayed maxima coinciding with the onset of the saturation stage. Anisotropy in fracture strain, observed between the axial and radial directions in a disk-like HPT sample, reduced with the randomization of shear texture, while higher intensities of the C {100}<110> orientation was considered responsible for the lower elongation-to-failure along the radial direction.},
  articleno    = {138195},
  author       = {Lanjewar, Harishchandra and Naghdy, Soroosh and Vercruysse, Florian and Kestens, Leo and Verleysen, Patricia},
  issn         = {0921-5093},
  journal      = {MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING},
  keywords     = {High pressure torsion,Commercial purity aluminum,Statistical boundary analysis,Tensile properties,Micro-texture,Work hardening,CHANNEL ANGULAR EXTRUSION,STRAIN-HARDENING BEHAVIOR,HALL-PETCH RELATION,RATE SENSITIVITY,STORED ENERGY,DISLOCATION BOUNDARIES,DEFORMATION STRUCTURES,NEUTRON-DIFFRACTION,NANOCRYSTALLINE,DUCTILITY},
  language     = {eng},
  pages        = {12},
  title        = {Severe plastically deformed commercially pure aluminum : substructure, micro-texture and associated mechanical response during uniaxial tension},
  url          = {http://dx.doi.org/10.1016/j.msea.2019.138195},
  volume       = {764},
  year         = {2019},
}

Altmetric
View in Altmetric
Web of Science
Times cited: